Owning the system

Do solar panels work in winter? Snow, cold, and short days

Yes. Solar panels make electricity from light, not heat, so they keep working through winter. Cold air even helps: a panel produces more power per hour of sun when its cells are cold than when they are hot. What winter takes away is not the panel's ability to work but the amount of light available: days are short, the sun sits low, and snow can cover the array for days at a time.

The split matters for the decision. The U.S. Department of Energy's winter guidance says panels produce useful power through all four seasons, and that a dusting of snow has little impact because wind blows it off and light scatters through a thin coating. Heavy snow is the real stop: covered cells make nothing until the snow slides or melts. The National Renewable Energy Laboratory's national snow model puts the annual cost of snow at 0 to 15.9 percent of a fixed rooftop array's yearly energy in the continental United States, with a median of 2.5 percent.

This guide separates the three winter effects, cold, short days, and snow, puts a number on each where a number exists, and ends with the steps that get a roof array through a winter without a service call. The snow numbers here are the summary; the city-by-city table lives in how much energy solar panels lose to snow.

The short answer: yes, with three winter discounts

Three things change in winter, and only one of them helps. Cold raises the power a panel makes from each hour of sunlight. Short days cut the number of those hours. Snow can block the light entirely until it clears. A system that looks weak in January is usually suffering from the second and third, not the first.

The cold gain is real but small next to the daylight loss. Four current residential datasheets put the power temperature coefficient at -0.24 to -0.377 percent per degree Celsius, which means output rises by that much for every degree the cells sit below their 25 degree C rating. The section below works the arithmetic for a cold, bright day. The daylight loss has no single number because it depends on latitude: the further north the roof, the shorter the winter day and the lower the sun.

Snow sits between the two. The NREL model says most roofs lose little to snow over a year, a median of 2.5 percent, but the range is wide: Phoenix and Los Angeles print 0.0 percent and Minneapolis 10.7 percent at a 20 degree tilt. Where a roof sits in that range decides whether snow deserves a plan or a shrug.

Why cold helps: the temperature coefficient, worked

A module rating is a laboratory number, printed at standard test conditions: 1,000 watts per square meter of light and a cell temperature of 25 degrees C (77 degrees F). The REC Alpha Pure-RX datasheet prints a Pmax temperature coefficient of -0.24 percent per degree C, and the four 2026 datasheets compared on this site span -0.24 to -0.377 percent per degree C. The minus sign means output falls as cells warm past 25 degrees, and rises as they cool below it.

Take a 400 watt panel on a bright winter day with its cells at 0 degrees C, 25 degrees below rating. At the REC coefficient the gain is 25 x 0.24 percent, or 6.0 percent, so the panel makes 424 watts from the same light. At the steepest coefficient in the range, -0.377 percent, the gain is 9.4 percent and the same panel makes 438 watts. The arithmetic is linear because REC states its coefficients are linear values, and it is an illustration at one light level, not a field measurement: real cells in sun run warmer than the air, and the gain applies to power at a given light level, not to the day's total energy.

The same effect runs in reverse in summer, which is why the heat guide finds a hot Phoenix hour costing 10 to 23 percent of rated power. Winter's cold is a genuine, if modest, offset to winter's short days. It is also why a production estimate that ignores temperature overstates summer and understates winter; the guide to reading a production estimate shows where the temperature assumption sits.

Cold-day gain for a 400 watt panel with cells at 0 degrees C, 25 degrees below the 25 degree C rating (checked November 7, 2026)
Temperature coefficientGain at 25 degrees below ratingOutput at the same light level
REC Alpha Pure-RX, -0.24% per degree C25 x 0.24% = 6.0%424 W
Steepest of the four 2026 sheets, -0.377% per degree C25 x 0.377% = 9.4%438 W

Short days are the real winter tax

Winter output falls mostly because there is less sun to collect. Days are shorter, the sun tracks lower across the sky, and a low sun throws longer shadows from trees, chimneys and neighbouring roofs, so shading that never matters in June can matter in December. Cloud cover adds a further cut on overcast days, though panels still produce from diffuse light.

Two consequences follow. First, a winter month will always look thin next to a summer month on the same roof, and that gap is normal, not a fault. The low production guide shows how to tell a seasonal dip from a real problem. Second, annual production estimates already include winter: they are built from a full typical weather year, so a quote's yearly kilowatt-hour figure has the short days priced in. Judge the system on the annual figure, not on a January bill.

One useful check: in the PVWatts typical-year runs behind this site's heat guide, December has the highest output per unit of sunlight of any month in Phoenix, because the cells run coldest. The light is scarce in winter, but each unit of it is used well.

Snow: what the national model says, and what the DOE adds

The Department of Energy's winter guidance is plain: a dusting of snow has little impact because wind blows it off and light forward-scatters through a sparse coating. Heavy snow prevents generation until it slides, and even a partial clearing restarts production, since exposed cells generate again once any part of the panel is uncovered. Melting snow also cleans the glass, washing away dirt as it runs off.

The NREL national study (Ryberg and Freeman, 2017) modeled snow loss at 239 stations over 30 winters, 1961 to 1990. At a 20 degree tilt the annual loss runs 0 to 15.9 percent across the continental United States with a median of 2.5 percent. Minneapolis averages 10.7 percent at 20 degrees and 9.5 percent at a tilt equal to its latitude of 44.9 degrees. Boulder loses 5.5 percent at 20 degrees and 3.9 at 40. The full city table, with each loss shown as years added to a 12-year payback, is in how much energy solar panels lose to snow.

Tilt helps snow slide: the same Minneapolis array loses less at latitude tilt than at 20 degrees, and the DOE notes that frameless modules shed snow more readily because there is no frame lip to hold it. That is a small factor in choosing a tilt, not a reason to steepen a roof array on its own: the annual production figure, not snow shedding, should set the tilt.

Annual snow loss at a 20 degree tilt, four cities from the NREL national study Bar chart of annual energy lost to snow at a 20 degree tilt: Phoenix 0.0 percent, Atlanta 0.1 percent, Boulder 5.5 percent, Minneapolis 10.7 percent. Median across the continental stations is 2.5 percent. 0.0%0.1%5.5%10.7%PhoenixAtlantaBoulderMinneapolisAnnual energy lost to snow, 20 degree tilt
Annual snow loss at a 20 degree tilt, four cities from the NREL national study Four stations from Table A-1 of the NREL report. Phoenix and Los Angeles both print 0.0 percent; Atlanta prints 0.1. The median across the continental stations is 2.5 percent. Source: Ryberg and Freeman, NREL/TP-6A20-68705 (2017), Table A-1, checked November 7, 2026.
Show the snow loss figures behind this figure
CityAnnual snow loss at 20 degree tilt
Phoenix0.0%
Atlanta0.1%
Boulder5.5%
Minneapolis10.7%

Get a roof array ready for winter in 7 steps

None of these steps needs a roof climb. The theme of the list is that winter care is mostly watching and waiting, with one tool, a soft broom, and one rule: never climb an icy roof to clear panels.

  1. Read the last production estimate and note the winter months it assumes, so a thin January does not read as a fault.
  2. Check the roof's snow history against the NREL table: below about 3 percent annual loss, snow needs no plan beyond patience.
  3. Look at the array from the ground after the first snow: if the lower rows stay covered for days while the upper rows clear, note the pattern for the installer.
  4. Clear only what you can reach from the ground with a soft broom, and only when heavy snow threatens the structure; the DOE's winter guidance says a broom, not a shovel.
  5. Keep gutters and drainage clear so melt water runs off the roof instead of pooling at the eaves and freezing into ice dams.
  6. If the system has a battery, check its cold-weather limits before the first freeze; lithium charging slows or stops below freezing, and the cold-weather battery guide lists four makers' stated floors.
  7. After the last storm of the season, have the array inspected if anything looks bent, loose or cracked; the DOE recommends a trained professional check after an extreme winter event.

What can go wrong: weight, ice, and the battery in the cold

Heavy snow is a structural load before it is a production problem. The DOE's winter hardening guidance says the weight of accumulated snow can warp or even break a module, and ice adds weight unevenly, straining frames and the structure below. Its pre-storm advice is to remove snow only when there is substantial accumulation and a risk of overloading with the incoming storm, gently, with a broom. If the load ever looks beyond the roof, the question belongs to a structural engineer, not to a ladder; the roof support guide covers the check.

Ice storms are a separate hazard from snowfall, and they hit different places: the DOE maps the highest ice-storm risk across the Great Plains and parts of the South, while the deepest January snowfalls, more than 30 inches on average, fall in mountain areas, the Great Lakes coasts and parts of Appalachia. A roof in either zone should have its racking and attachments checked against local snow and ice loads at design time, not after the first storm.

The battery is the part of the system most likely to notice the cold. Lithium cells charge slowly or not at all below freezing, and several makers describe heaters that spend energy keeping cells warm. That cost is small next to a day of lost charging, but it is the reason a battery in an unheated garage deserves its own check before winter. See do home batteries work in the cold for the documented limits.

Should winter change the buy decision?

For most buyers, no. Winter trims the year's output by a few percent in most of the country and by about a tenth in the snowiest cities, and those losses are already inside the annual production figure a quote should show. A system that pays back in 12 years without snow pays back in about 13.4 years at Minneapolis's 10.7 percent snow loss, as the worked example below shows. That is a real cost, and it is not a reason to walk away from a roof that otherwise works.

Winter should change the decision in three cases. If the roof faces north or is heavily shaded in winter, the short-day penalty stacks on the shade penalty and the annual figure will show it. If the site sits in the deep-snow zone and the roof is shallow, ask the installer what tilt and snow assumption the estimate used. And if the home loses power in winter storms, the decision is really about a battery, not the panels: panels alone do not keep the lights on in an outage, as does solar work in a power outage explains.

Each winter factor, what it does, and the response it earns (checked November 7, 2026)
Winter factorEffect on the systemWhat to do
Cold airRaises power per hour of sun, 6 to 9 percent on a cold bright day at the datasheet coefficientsNothing; it is a small credit, not a problem
Short daysCuts total winter output; the year's figure already includes itJudge the system on the annual estimate, not a January bill
Snow cover0 to 15.9 percent of annual energy, median 2.5 percentWait for slide and melt; clear heavy loads with a broom only
Ice and weightCan warp modules and strain rackingCheck snow and ice loads at design time; inspect after extreme events
Battery in the coldLithium charging slows or stops below freezingCheck the maker's stated floor before the first freeze

A worked example: Minneapolis snow on a 12-year payback

Take the DOE Q1 2025 benchmark price for an 8 kW residential system: $2.95 per watt, or $23,600 in 2024 dollars, with no federal residential credit in the figure. Suppose the quote's annual production value implies a 12-year simple payback, so the system returns $23,600 divided by 12, or $1,967 of production value a year.

Minneapolis loses 10.7 percent of annual energy to snow at a 20 degree tilt in the NREL model. The snow-free value of $1,967 falls by 10.7 percent to $1,757, a loss of $210 a year. Simple payback stretches from 12 years to 12 divided by (1 minus 0.107), which is 13.4 years, adding 1.4 years. At the median station's 2.5 percent loss the same arithmetic adds 0.3 years.

All three numbers are labelled: the price is the national benchmark, not a local quote; the 12-year payback is an assumption, not a measured figure; and the snow loss is a modeled average over 1961 to 1990 weather, not a measurement on any one roof. Replace the assumed payback with the one on the actual quote and the same division gives the snow cost for that roof.

Where this goes wrong

Climbing onto an icy roof with a shovel to clear panels. The DOE's guidance is explicit: a broom, not a shovel, and only when the snow load threatens the structure. A scratched or cracked panel costs more than the day of production it saves, and a fall costs more than the system.

Reading a January bill as a broken system. Winter months are supposed to be thin. Compare the year's total against the estimate, not one month against another.

Buying a steeper tilt, a snow guard, or a heating kit to chase a 2.5 percent median loss. At most roofs the money buys more production spent on panels than on snow equipment.

Before the first snowfall

  • Note the winter months in the production estimate, so January reads as expected, not as a fault.
  • Find the roof's snow loss in the NREL city table; under about 3 percent, no snow plan is needed.
  • Buy a soft broom with a long handle if the array is reachable from the ground; leave the shovel in the garage.
  • Clear gutters and drainage before the first freeze.
  • Check the battery's cold-weather charging limits and heater behaviour before the first cold snap.
  • Write down the installer's number and the roof's snow-load rating, so a heavy storm has a plan attached.

Questions readers ask

Do solar panels work when they are covered in snow?

No, not while fully covered: covered cells receive no light. Light snow is different: wind blows it off, light scatters through a thin coating, and production resumes as soon as any part of a panel is exposed. The NREL model puts the annual cost of snow at a median of 2.5 percent of yearly energy, so a covered week is a small loss inside the year's total.

Do solar panels work on cloudy winter days?

Yes, at reduced output. Panels produce from diffuse light as well as direct sun, so an overcast day still generates, just less. The winter penalty is mostly the short day and the low sun, not the cloud alone.

Is winter a bad time to install solar panels?

Installation can happen in winter, and crews work through it in cold states; the constraint is weather on the install days, not the season. What matters more is the roof: a roof near the end of its life should be replaced before panels go on, in any season.

Can cold damage solar panels?

Panels are built for it: the REC datasheet in the sources rates its module down to -40 degrees F (-40 degrees C). The cold itself improves output per hour of sun. The risks are structural, heavy snow load and ice, not the temperature of the cells.

Should I clear snow off my panels?

Usually no. Most snow slides or melts off a tilted array on its own, and the annual loss is small. Clear only heavy accumulation that threatens the structure, gently with a soft broom from the ground, never with a shovel and never by climbing an icy roof.

Will snow wreck my payback?

At the median station it adds about 0.3 years to a 12-year payback; at Minneapolis's 10.7 percent it adds about 1.4 years. The worked example above shows the division. Because annual estimates already include a typical winter, a quote that shows its snow assumption is the one to trust.

Sources and verification

The snow figures are modeled averages for weather stations using 1961-1990 data and one array layout; they are not measurements on any roof. The cold-day gain is linear arithmetic at one light level and one coefficient, and real cells run warmer than the air. Production figures are planning factors until a roof-specific PVWatts model exists.