Solar panels for RVs and campers: sizing, cost, and what actually works
An RV solar system is a small off-grid system with a roof that moves. The sizing arithmetic is the same as a cabin's: list the loads, turn them into watt-hours a day, divide by peak sun hours, and size the battery to carry the loads through the night and a cloudy day. What changes is the constraint: a camper roof holds only so many panels, and the battery has to fit in a compartment built for something else.
Two manufacturer sizing guides agree on the shape of the answer. Battle Born's rule is about 200 watts of solar per 100 amp-hours of lithium battery, so a 200 amp-hour bank pairs with 400 to 600 watts of panels. Renogy's method works from daily watt-hours instead: divide the day's use by peak sun hours, then divide again by the charge controller and inverter efficiencies. Both methods land a weekend camper at 200 to 400 watts and a full-timer at 400 to 600 watts, with a 100 to 200 amp-hour lithium bank underneath.
This guide runs both methods on one worked example, prices the parts the honest way, and names the things that do not work: running a rooftop air conditioner off panels, and buying hardware before measuring the roof. The home version of the same arithmetic, with December sun and a generator in the plan, is in how much off-grid solar costs.
The short answer: what most RVs actually need
Three use cases cover most rigs. A weekend camper who runs lights, phones, a fan and a 12 volt fridge for two or three days needs 200 to 400 watts of panels and a 100 to 200 amp-hour lithium bank. A full-timer without air conditioning, working from the rig with a laptop and a dish, needs 400 to 600 watts and 200 to 300 amp-hours. A rig that must run a microwave or a rooftop air conditioner off-grid needs a generator as well; panels alone do not get there, and the section below shows why.
The table is a planning band, not a quote. The worked example below shows where the middle numbers come from, and the six steps after it show how to replace them with the rig's own loads.
| Use case | Daily use, planning band | Panels | Lithium bank | Charge controller |
|---|---|---|---|---|
| Weekend camper | 600 to 900 Wh | 200 to 400 W | 100 to 200 Ah | 30 A MPPT |
| Full-timer, no air conditioning | 1,200 to 2,400 Wh | 400 to 600 W | 200 to 300 Ah | 50 A MPPT |
| Anything with air conditioning | 3,000 Wh and up | Roof space runs out first | 300 Ah and up | Generator in the plan |
Size it in 6 steps
The order matters: loads first, panels second, battery third, roof last as a reality check. Buying panels first is how rigs end up with an array that fits the roof and starves the battery, or a battery the roof cannot refill.
- List every load with its watts and its hours a day, from the label or the manual, not from memory. A 12 volt compressor fridge is the big one; a laptop, lights, fan, phones and water pump fill out the list.
- Multiply watts by hours for each load and add them up. The total is the day in watt-hours. The worked example below totals 900.
- Divide the day's watt-hours by peak sun hours for the season and place, usually 4 to 5 in much of the United States in summer, less in winter. That is the panel watts before losses.
- Divide by the charge controller efficiency, 0.94 for MPPT and about 0.8 for PWM in Renogy's method, and again by 0.9 if an inverter feeds AC loads. That is the panel watts to buy.
- Size the battery from the same day: divide watt-hours by 12 volts for amp-hours, then double it for lead-acid, which should not drain past half, or divide by 0.8 for lithium, which can use about 80 percent. Add a cloudy-day buffer if the rig sits still for days.
- Check the roof before ordering anything: measure the flat space between vents, air conditioners and skylights, and check the controller's maximum input watts for the array in step 4.
Show the sizing chain figures behind this figure
| Step | Division | Result |
|---|---|---|
| Daily loads | 480 + 80 + 180 + 120 + 40 Wh | 900 Wh |
| Panel watts before losses | 900 Wh / 4 peak sun hours | 225 W |
| Panel watts after losses | 225 W / 0.94 / 0.9 | 266 W, buy 300 W |
| Battery, lithium | 900 Wh / 12 V / 0.8 usable | 94 Ah, buy 100 Ah |
| Controller | 300 W / 12 V | 25 A, buy 30 A MPPT |
A worked example: a weekend camper's 900 watt-hour day
Take a weekend camper with five loads, each labelled with its watts and hours. A 12 volt compressor fridge at 60 watts running 8 hours: 480 watt-hours. LED lights at 20 watts for 4 hours: 80. A laptop at 60 watts for 3 hours: 180. Phones and a fan at 30 watts for 4 hours: 120. A water pump and odds and ends: 40. The day totals 480 plus 80 plus 180 plus 120 plus 40, or 900 watt-hours.
Panel watts by Renogy's method, at 4 peak sun hours: 900 divided by 4 is 225 watts before losses. Divide by 0.94 for an MPPT controller, 239 watts, and by 0.9 for the inverter, 266 watts. Round up to 300 watts of panels, and 400 watts if the roof allows it, which is the 20 to 30 percent extra capacity Battle Born recommends for real-world conditions.
Battery by the same method: 900 watt-hours divided by 12 volts is 75 amp-hours. Double it for lead-acid, 150 amp-hours, or divide by 0.8 for lithium, 94 amp-hours, so a 100 amp-hour lithium battery. Cross-check by Battle Born's rule: 200 watts of solar per 100 amp-hours of lithium, so a 100 amp-hour bank pairs with 200 watts minimum, and the 300 watt array sits above it. The controller: 300 watts at 12 volts is 25 amps, so a 30 amp MPPT controller, which Renogy rates for up to 400 watts on 12 volts, fits with room to grow.
Every input above is labelled: the loads are a stated weekend pattern, not a measurement, and 4 peak sun hours is a summer planning figure for much of the United States. Replace the loads with the rig's own, measured over a week with a battery monitor, and the same divisions give the rig's own answer.
Roof space is the binding constraint
Battle Born's sizing guide makes the point directly: on RVs, vans and boats, roof space may restrict how many panels can be installed, and panel layout and efficiency then matter more than total wattage. A camper roof is already crowded with the air conditioner, vents, skylight and antenna, and the flat runs between them are what is actually available. Measure those runs and compare them with the panel dimensions on the datasheet of the panel being bought; no rule of thumb replaces the tape measure.
Three things help when the roof is short. Tilt brackets add output in winter and in northern latitudes, where a flat panel sees the sun at a sharp angle. Portable panels, set on the ground in the sun while the rig sits in the shade, add watts without roof space, at the cost of setup time and a cable to trip over. And a DC-DC charger, which charges the house battery from the alternator while driving, covers the miles between campsites, so the panels only have to keep up while parked.
Shading deserves the same respect it gets on a house roof: one shaded cell string can drag a whole series string down, and a roof vent casts a shadow that moves across the array all day. The shade guide explains why partial shade costs more than its area suggests, and why panel-level electronics exist.
Lead-acid vs lithium: the battery decision
Most RVs arrive with a lead-acid house battery, and the first upgrade question is whether to keep it. Renogy's method doubles the day's watt-hours when sizing lead-acid, because draining past half shortens its life; lithium, by contrast, can use about 80 percent of its capacity day after day. On the worked example's 900 watt-hour day, that is 150 amp-hours of lead-acid against 100 amp-hours of lithium at 12 volts.
Lithium also charges faster and weighs about half as much for the same usable energy, which matters in a vehicle with a weight limit. Its limits are cold and cost: lithium charging slows or stops below freezing, so a battery in an unheated bay needs a heater or a warm parking spot, and the upfront price is higher. The cold-weather battery guide lists the documented charging floors. Lead-acid remains the honest choice for a rig that camps only in summer and already owns the battery.
Whatever the chemistry, the charger must match it: an older converter built for lead-acid can undercharge lithium, and a lithium-ready charger is part of the upgrade, not an optional extra.
Charging while you drive: the DC-DC charger
The panels earn their keep while parked, and the alternator earns its keep while driving, but the two charging sources are not interchangeable. An alternator is built to refill a starter battery after a few seconds of cranking, not to recharge a deep-cycle lithium bank. Battle Born's lithium charging guide puts it plainly: alternators are designed for starting batteries, not deep-cycle lithium systems, and connecting them directly can cause high current surges or voltage mismatches. That is what a DC-DC charger, also called a battery-to-battery charger, is for: it takes power from the alternator, regulates it to the precise voltage and current the lithium bank needs, prevents alternator overload, and lets a lead-acid starter battery and a lithium house bank coexist in one rig.
Size the charger to the bank and to how much the rig moves. Renogy's 40 amp DC-DC MPPT charger lists 40 amps maximum output current, 616 watts output power, and 93 percent charging efficiency. At 40 amps, two hours of driving returns about 80 amp-hours, or about 960 watt-hours at 12 volts, which is roughly the worked example's whole 900 watt-hour day. That is the device's real job on a rig that moves most days: the drive replaces a day of sun. A rig that sits for a week still lives on the panels, and a rig that drives an hour between campsites gets a partial day back, not a full one.
Newer chassis complicate the wiring. A smart alternator varies its output with driving conditions, so a charger that only watches voltage can misread it and never start. Renogy's product page says a smart alternator needs the charger's IGN cable connected through the vehicle ignition port, while a traditional alternator works on voltage sensing alone, starting when the starter battery reaches 13.2 volts. If a new charger never starts on a newer rig, the IGN wire is the first thing to check. Renogy's 30 amp and 50 amp models take solar and alternator input at the same time; the 40 amp model switches between the two inputs based on availability, so it charges from one source at a time.
Two limits stay with the device. First, cold: Battle Born lists 32 to 113 degrees Fahrenheit as the ideal charging range for lithium, so a DC-DC charger does not solve a frozen battery bay, and charging still waits for the battery to warm above freezing; the cold-weather battery guide lists the documented charging floors. Second, scale: for a rig that drives most days, Battle Born notes a second alternator with a dedicated regulator can become the primary charging source, which is a bigger job than a DC-DC charger and belongs in a build plan, not a first solar kit. The DC-DC charger is the middle step: it fits at the start of a build, and it is the piece that keeps the alternator safe while it works.
What it costs: the five lines on the bill
An RV solar bill has five lines: panels, battery, charge controller, inverter, and mounting plus wiring plus fuses. The panel line can be compared against the DOE residential benchmark of $2.95 per watt, which prices the worked example's 300 watts at $885 in 2024 dollars. That is a comparison line for the panels alone, not a kit price: RV panels, mounts and small-quantity hardware cost more per watt than a residential rooftop array, and the benchmark does not cover the battery, controller, inverter or labour.
The battery is usually the largest line. Compare batteries by dollars per usable kilowatt-hour, not by the sticker price: a 100 amp-hour lithium battery at 12 volts holds 1,200 watt-hours gross and about 960 usable, so its price divided by 0.96 is the comparable figure. A lead-acid battery of the same label holds the same gross energy but only about 600 usable watt-hours, so the same division runs against half the energy.
Get the total as one number before ordering, and compare two quotes the same way: total price divided by panel watts, and total price divided by usable battery kilowatt-hours. A kit that looks cheap on panels and hides the controller, wiring and fuses in a second order is not cheap.
What actually works, and what does not
What works: an MPPT controller on any array above a couple of hundred watts, because it recovers the panel voltage a PWM controller throws away; Renogy puts MPPT at about 94 percent efficiency against about 79 to 80 percent for PWM. A pure sine wave inverter for anything with a motor or a sensitive charger. A battery monitor with a shunt, so the day's use is measured instead of guessed. Fuses and wire sized to the controller's manual, not to the nearest spool in the shop.
What does not work: running a rooftop air conditioner from a weekend-size array. A rooftop air conditioner is a kilowatt-scale load, and at 1,000 watts one hour of cooling consumes about 1,000 watt-hours, which is the worked example's whole day of production. That is a generator load, or a shore-power load, and any plan that promises otherwise is selling panels.
Portable power stations deserve a mention as the no-wiring alternative: a station with a folding panel charges phones, lights and a laptop with no roof work at all, and it is the right answer for a renter or a rig that camps with hookups most nights. It is not a substitute for a roof array on a full-timer, because its battery and panel are sized for a weekend, not a season.
Where this goes wrong
Buying panels before measuring the roof. The array that fits the budget often does not fit between the air conditioner, the vents and the skylight, and the return shipping costs more than the panels saved.
A PWM controller on a 400 watt array. At Renogy's efficiencies the PWM throws away about 15 percent of the array's output against an MPPT, which is a whole panel's worth on a three-panel roof.
Undersized wire and missing fuses. A 30 amp charge circuit on thin wire drops voltage and heats up; the fuse belongs as close to the battery as the manual allows, not at the far end of the run.
Expecting the alternator to do the panels' job, or the panels to do the alternator's. Driving charges while moving; panels charge while parked. A rig that does both needs both, and a DC-DC charger is the bridge between them.
Before you buy anything
- Measure the flat roof space between every fitting, and write down the panel dimensions from the datasheet of the panel being bought.
- List the loads with watts and hours, and total the day in watt-hours.
- Run the two sizing methods and check they agree within a panel or two; if they do not, the load list is wrong.
- Confirm the charge controller's maximum input watts and the battery's charging profile match the array and the chemistry.
- Count the fuses, the wire gauge, the mounts and the sealant in the total before comparing prices.
- Plan where the battery lives, and whether that bay stays above freezing when the charger needs to run.
Questions readers ask
How many solar panels do I need for my RV?
Work from the day's watt-hours, not from a panel count. A weekend camper at about 900 watt-hours a day needs about 300 watts of panels at 4 peak sun hours by Renogy's method, and a full-timer at 2,400 watt-hours needs 600 watts by Battle Born's example. The worked example above shows the divisions; measure the rig's own loads for a week before ordering.
Can I run my air conditioner off RV solar?
Not from a weekend-size array. A rooftop air conditioner is a kilowatt-scale load: at 1,000 watts, one hour of cooling consumes about 1,000 watt-hours, the worked example's whole day of production. Air conditioning off-grid is a generator or shore-power load; solar covers the fridge, lights, laptop and fan.
Rigid, flexible, or portable panels?
Rigid panels are the default: cheapest per watt, longest lived, and the easiest to tilt. Flexible panels suit curved roofs but run hotter and age faster. Portable panels need no roof work and move into the sun, but they must be set up and packed away each stop. Many rigs end up with rigid panels on the roof and one portable panel for shade days.
Do I need a special charge controller?
An MPPT controller, sized to the array: 30 amps for up to 400 watts on a 12 volt system by Renogy's rating. A PWM controller works on a small array but gives up about 15 percent of the output. The controller must also match the battery chemistry, lithium or lead-acid, in its charging profile.
Will the panels charge while I am driving?
No, not from the panels alone in any useful sense; driving charges the house battery through the alternator and a DC-DC charger. The panels earn their keep while parked. A rig that moves most days can lean on the alternator; a rig that sits for a week lives on the panels.
Can I add more panels later?
Yes, if the controller and the wire were sized for it. Leave headroom in the controller's maximum input watts and in the roof layout, and buy the same panel model so the strings match. Adding a second, different panel later usually means a second controller.
Do I need a DC-DC charger, or can the alternator charge the house battery directly?
For a lithium house bank, yes, fit one. Battle Born's charging guide warns that an alternator is designed for a starting battery, not a deep-cycle lithium bank, and connecting the two directly can cause high current surges or voltage mismatches that overload the alternator. A DC-DC charger regulates the charge to the lithium profile, about 14.2 to 14.6 volts on a 12 volt system, and lets a lead-acid starter battery and a lithium house bank coexist. Size it to the driving pattern: a 40 amp charger returns about 80 amp-hours in two hours of driving, roughly the worked example's whole day. On a smart-alternator chassis, connect the charger's ignition wire, or it may never start.
Sources and verification
- Renogy, Sizing Your Off-Grid Solar System with Solar Calculator (updated April 29, 2026): Read November 7, 2026: load sizing in watt-hours; panel watts as daily watt-hours divided by peak sun hours, divided by 0.8 for PWM or 0.94 for MPPT and by 0.9 for an inverter; battery amp-hours as watt-hours divided by volts, doubled for a 50 percent depth of discharge; a 30 amp controller handles 400 watts on 12 volts; worked example totals 6,850 watt-hours and 2,024 watts. Checked November 7, 2026.
- Battle Born Batteries, How to Size Solar Panels for a Deep Cycle Battery System (published May 20, 2026, updated June 3, 2026): Read November 7, 2026: about 200 watts of solar per 100 amp-hours of LiFePO4 battery; 2,400 watt-hours a day at 4 peak sun hours needs 600 watts; add 20 to 30 percent extra capacity for real-world conditions; roof space is the limiting factor on RVs, vans and boats. Checked November 7, 2026.
- U.S. Department of Energy, Solar Photovoltaic System Cost Benchmarks (Q1 2025): Read November 7, 2026: Table 2, residential 8 kW DC PV-only system, modeled market price $2.95 per watt DC (minimum sustainable price $2.78), in 2024 dollars, owner tax credits and subsidies excluded. Used here only as a comparison line for the panel watts, not as an RV kit price. Checked November 7, 2026.
- SolarRoost methodology: the DOE residential benchmark comparison line: Residential cost benchmark of $2.95 per watt DC: the U.S. Department of Energy's Q1 2025 modeled market price for an 8 kW system, in 2024 dollars, the comparison line this site uses for all cost examples, checked October 30, 2026. A benchmark for comparison, never a quote or local price survey. Checked October 30, 2026.
- Battle Born Batteries, Charging Lithium Batteries: The Basics (published November 26, 2025, updated September 4, 2026): Read November 8, 2026: alternators are designed for starting batteries, not deep-cycle lithium systems, and direct connection can cause high current surges or voltage mismatches; DC-to-DC chargers regulate voltage and current, prevent alternator overload, and let different chemistries coexist; 12 volt lithium full charge around 14.2 to 14.6 volts; ideal charging range 32 to 113 degrees Fahrenheit; a second alternator with a dedicated regulator can be the primary charging source for heavy drivers. Checked November 8, 2026.
- Renogy, 12V 40A DC-DC MPPT Battery Charger (RBC40D1S): Read November 8, 2026: 40 amps maximum output current, 616 watts output power, 93 percent charging efficiency; traditional alternator input 13.2 to 16.0 volts DC, smart alternator (Euro 6) 12 to 16.0 volts DC; a smart alternator needs the IGN cable connected through the vehicle ignition port; 30 amp and 50 amp models take solar and alternator input simultaneously, the 40 amp model switches between inputs based on availability. Checked November 8, 2026.
The load list is a stated weekend pattern, not a measurement, and 4 peak sun hours is a summer planning figure. Panel dimensions, roof space and battery placement vary by rig; the sizing here is a planning method, not a design, and wiring and fusing follow the component manuals.