How to read your solar monitoring app: production, consumption and the panel map
The app on your phone is the only part of your solar system you will look at every week, and it is also the part most owners misread. It shows production, which is what your panels made, and it may show consumption, which is what your home used, and those two numbers answer different questions. Confusing them is how a healthy system looks broken, and how a broken panel hides behind a healthy-looking total.
This guide reads the two apps most American homeowners actually get: Enphase Enlighten, for systems with Enphase microinverters, and SolarEdge mySolarEdge, for systems with a SolarEdge inverter and power optimizers. Both are free for system owners, both show the same four numbers in different places, and both need the same checks: the dashboard, the flow diagram, the panel map, and the alerts. The figures come from the app guides read for this page and from the site's verified PVWatts record; no figure here is a guess, and every worked example prints its inputs.
The short answer: four numbers on the dashboard
Open the app and you are looking at four numbers, whether the app says Enphase or SolarEdge. Learn what each one is before you worry about any of them, because three of the four are totals over different periods, and the one that is not a total is the only one that changes minute by minute.
Read the table down the last column. Current power is the only live number, and it is zero at night by design. Energy today is the running total since sunrise. The month and year totals are for comparing against the estimate and the bill. Lifetime energy is the running tally since the system was switched on, and on Enphase it counts AC energy, the usable electricity after conversion, not the DC energy the panels produced before the microinverters converted it.
| Number | What it is | Where to find it | What it tells you |
|---|---|---|---|
| Current power (kW) | Power being produced right now | Dashboard, top of the screen | Whether the system is producing at this minute, and roughly how hard |
| Energy today (kWh) | Energy produced since sunrise | Dashboard, under current power | How the day is going so far, against yesterday and the weather |
| Energy this month / year (kWh) | Totals for the calendar month and year | Dashboard or the history view | Whether the month is tracking the estimate |
| Lifetime energy (kWh) | Total produced since switch-on | Dashboard, prominent on Enphase | The long-run tally; on Enphase it is AC energy after conversion |
Production is not consumption: the two views and the missing sensor
The most common confusion in either app is the gap between production and consumption. Production is what your panels generated. Consumption is what your home used. The app can show production on its own, because the inverter or microinverters measure it directly. It can only show consumption if the installer fitted extra sensors, called current transformers or CTs on Enphase systems, or a consumption meter on SolarEdge systems, that measure the energy flowing into your home.
On Enphase, the app opens in production view by default, and you switch to consumption view to see both numbers together: what the panels are producing, what the home is consuming, and whether you are net exporting to the grid or net importing from it. If your system has no CTs, the consumption view will be missing or wrong, and a home that is clearly using power can show zero consumption. That is a missing sensor, not a broken system, and the fix is asking the installer to fit CTs.
The same rule holds on SolarEdge. Without a consumption meter the app shows production data only, with no information about how much energy your home is using or whether you are importing or exporting. The energy flow diagram, the screen that shows where power is going, only appears when the meter is installed.
Keep the two numbers apart with a worked example from the Enphase guide. Suppose your panels produce 30 kWh in a day and your home uses 15 kWh while the sun is up. The app will show 30 kWh of production, and your utility will credit you for the 15 kWh you exported. The other 15 kWh was consumed in real time by your home. That is the better outcome, not a loss: the energy you use yourself avoids the retail rate, while exported energy is usually credited at a lower rate. If you want to track how much of your production is self-consumed versus exported, you need consumption monitoring switched on, which needs the sensors fitted.
The energy flow diagram: follow the arrows
Both apps have a screen that draws the energy as arrows between three points: your panels, your home, and the grid. If you have a battery, a fourth point appears, showing charge and discharge and the state of charge as a percentage. This is the screen to open when the question is where the power is going, rather than how much was made.
Read the arrows, not the totals. An arrow from solar to home means you are using what you produce. An arrow from solar to grid means you are exporting the excess, and earning whatever export credit your utility pays. An arrow from grid to home means your panels are not covering the load at that moment, which is normal in the evening, and is a problem at noon on a clear day only if the production number is also low.
The diagram is live, so it changes through the day. At midday on a clear day it should show solar feeding the home with the rest going to the grid. In the evening it should show the grid feeding the home, and the solar arrow gone. If the diagram shows nothing at midday on a clear day, check the dashboard total first: a diagram with no arrows and a dashboard showing normal production is a display problem, and a diagram with no arrows and a dashboard showing zero is a production problem. The lower-than-expected guide works through that split in full.
The panel map: one square per panel
The feature that makes these apps worth opening is the panel map: a drawing of your roof where each square is one panel, coloured by how that panel is performing. On Enphase it is the Array View, reached from the app menu. On SolarEdge it is the Layout tab, showing the power optimizer map, and only if your installer granted you layout access; if you do not see the tab, ask the installer to upgrade your permissions, because there is no technical reason to withhold it.
Tap any square to see that panel's own numbers. On Enphase you get its current output in watts, its total energy today, and whether the microinverter behind it is communicating. On SolarEdge you get current power in watts, voltage and current from that specific optimizer, and whether the optimizer is communicating. Bright colours mean the panel is producing well; grey or dark squares mean it is underperforming or offline, and a panel that is blacked out is not producing at all.
One panel below its neighbours is the pattern to learn. The Enphase guide puts the investigate line at 20 to 30 percent below the neighbouring panels, sustained rather than for an hour. Shade from a new tree, dirt, leaves, bird droppings, or a failing microinverter or optimizer are the usual causes, and the map tells you which panel to look at instead of guessing from the system total.
Run the check on a labelled example. Take a 20-panel system of 400-watt panels, which is 8,000 watts, or 8 kW. At midday on a clear day, suppose 19 panels read about 320 watts each and one reads 210 watts. The gap is 320 minus 210, or 110 watts, and 110 divided by 320 is 34 percent below its neighbours. That is past the 20 to 30 percent investigate line, so the panel is worth a look on the roof and a note to the installer, with the screenshot and the date. The 320-watt reading is itself a labelled illustration, not a promise: panels rarely read nameplate wattage at midday, because heat and the angle of the sun take a share, and the comparison that matters is panel against panel on the same roof at the same minute.
How fresh is the number: update intervals and the offline gateway
Neither app is truly live. Enphase Enlighten updates every 15 minutes, so the number on your screen can be a quarter of an hour old. The SolarEdge dashboard updates every few minutes during daylight hours. A reading that has not moved for an hour on a sunny day is stale data, not a dead system, and the first check is the last-updated time on the screen, then your home internet.
The box that sends the data is the gateway. On Enphase it is the IQ Gateway, and older systems use a device called the Envoy that does the same job. It gathers readings from every microinverter over your home wiring and uploads them through your internet connection. On SolarEdge the inverter itself reports, and its display shows S_OK when it is communicating with SolarEdge's servers.
The important fact about a gateway that goes offline is what does not happen: your panels keep producing power. You only lose the monitoring view. The most common cause is a WiFi problem, a new router, a new internet provider, or a changed password, and the usual fix is restarting the router or reconnecting the gateway to the WiFi network. On Enphase, four blinking red lights on the gateway usually mean a hardware failure, and the gateway warranty is five years, so note the light pattern before you call.
Tell a communication error from a production loss before you book a service call. A communication error looks like this: the inverter display shows a green light or S_OK and normal operation, the app shows no data or a last-updated time days old, and your utility bill still shows normal solar credits. A real production loss looks like this: the inverter shows an error code or fault message, the app shows a sharp drop in daily energy with no weather to explain it, or one or more optimizers appear grey in the layout view and read zero volts and zero watts when tapped. The first is a network job; the second is a solar job.
Alerts: turn on the two that catch real problems
An app you never open cannot warn you, and both apps need their alerts switched on. On Enphase, open Settings, then Notifications, and enable at least the system offline alert, which fires when the IQ Gateway or Envoy stops reporting, and the microinverter not reporting alert, which fires when one or more panels stop communicating. The low production alert fires when the system produces significantly less than expected for the weather and its own history. Alerts arrive by email, push notification, or both.
SolarEdge is the awkward one: the mySolarEdge app does not send push notifications, so a blown fuse or a stopped system tells nobody until someone opens the app. Email alerts exist, but they are set up through the web monitoring portal, not the app, under Admin and Alerts, and your installer controls the default settings and may have them routed only to their own email. Ask the installer to add your email to the alert list, or to grant you admin access so you can set them yourself. The guide's suggested threshold is a low production alert at 70 to 80 percent of expected daily output, low enough to avoid false alarms on cloudy days and high enough to catch a real problem.
Expect some false alarms and do not switch the alerts off because of them. Enphase notes that alert thresholds are sometimes set too conservatively by default, which produces nuisance alerts on cloudy days; the sensitivity can be adjusted in settings, or tuned with the installer. A system that alerts once on a cloudy week and never again is working. A system that never alerts because the alerts were never switched on is the one that discovers a dead string on the next utility bill.
When the app and the bill disagree
The app and the utility bill measure different things, so they will never match exactly, and a small gap is normal. The app shows what your panels produced. The bill shows what you exported to the grid. On a day your home uses 15 kWh while the panels make 30 kWh, the app says 30 and the bill credits 15, and both numbers are right.
The Enphase guide puts the normal gap between the app total and the utility export credits at 2 to 5 percent. Three things cause it: the app updates every 15 minutes while the utility meter is continuous, so small timing differences add up; the utility meter sits at the service panel and counts energy your home consumes between the inverter and the meter, including circuit losses; and consumption sensors fitted in the wrong place skew the numbers. A gap inside 2 to 5 percent needs no action. A gap bigger than that is worth investigating, starting with whether the sensors are fitted and fitted in the right place.
The stranger case is the bill crediting more energy than the app says you produced. That usually means the consumption sensors are installed backwards or in the wrong location, so the app misreports the direction of flow. That is a wiring job for the installer, not a metering problem, and it is worth fixing promptly, because every reading the app gives until then is suspect.
One more mismatch to expect: the lifetime energy figure on Enphase counts AC energy, the usable electricity that comes out of the microinverters after conversion, and it does not include the small amount lost during DC to AC conversion, typically 2 to 4 percent. That is the right number to track, because it is what actually flows into your home and onto the grid, but it will sit below any DC figure a datasheet or a quote uses, and the gap is conversion, not a fault.
The monthly check: compare against the estimate, not the average
The check that catches slow problems is a monthly one, and it needs the right comparison. Take the system size and the planning factor this site uses, 1,400 kWh per kW per year, and an 8 kW system should make about 11,200 kWh in a year. Divide by 12 and the average month is about 933 kWh. That average is the trap: a winter month will run well below it and a summer month well above it, so a January total of 700 kWh is not 25 percent short, it is January.
Compare the month against the same month last year, if the system has run a full year, or against the monthly figures from a PVWatts run for your address, which models each month from 30 years of weather data. The production estimate guide shows how to run that check input by input, and what the 14 percent losses line means. A month that lands within a few percent of the PVWatts figure for that month is a healthy system; a month 20 percent below it, with no weather to explain it, is the point to open the panel map and look for the grey square.
Keep the check short enough to do every month, and write the number down. The app keeps history, but a notebook line with the month, the app total, and the PVWatts figure for that month is what turns a vague feeling that production is falling into a dated record you can hand an installer. If the shortfall persists for two months, that record is the start of the case the lower-than-expected guide builds.
- Open the app and note the energy for the month just ended.
- Write it next to the PVWatts monthly figure for your address, or the same month last year.
- If the gap is more than about 20 percent, open the panel map and check every square.
- If one panel is grey or well below its neighbours, screenshot it with the date.
- If the whole system is low with no grey panels, check the gateway and the inverter display for a communication fault.
- Send the installer the month total, the PVWatts figure, and the screenshot, not a feeling.
One grey square and one short month: the two checks
Take a 20-panel system of 400-watt panels, which is 8,000 watts, or 8 kW. At midday on a clear day, 19 panels read about 320 watts each and one reads 210 watts. The gap is 320 minus 210, or 110 watts, and 110 divided by 320 is 34 percent below its neighbours. That is past the 20 to 30 percent investigate line in the Enphase guide, so the panel is worth a look on the roof and a note to the installer, with the screenshot and the date. Now run the monthly version of the same check. An 8 kW system at this site's planning factor of 1,400 kWh per kW per year should make about 11,200 kWh a year, or about 933 kWh in an average month. A January total of 700 kWh is 233 kWh below that average, which is 25 percent, but January is a short, low-sun month, so the honest comparison is the PVWatts figure for January at your address, or the same January last year. A month 20 percent below that comparison, with no weather to explain it, is the point to open the panel map.
Monthly app check to keep
- Know which app your system uses, and that the login came from the installer at commissioning.
- Check the dashboard weekly: current power, energy today, and the last-updated time.
- Confirm whether consumption sensors or a consumption meter are fitted, and what the app can show without them.
- Turn on the offline and low-production alerts, and add your email to the SolarEdge alert list.
- Open the panel map monthly and look for a grey square or a panel 20 to 30 percent below its neighbours.
- Write the month total next to the PVWatts figure for that month, and keep the record.
Reading your solar monitoring app, answered
Why does my monitoring app show zero at night?
Because the panels are not producing. Current power falls to zero after sunset by design, and energy today stops climbing until sunrise. Zero at night is normal; zero at noon on a clear day is not, and the first check then is the last-updated time, then the inverter display.
Why does my app show production but no consumption?
Because the sensors that measure what your home uses were never fitted. Enphase needs current transformers, called CTs, and SolarEdge needs a consumption meter; without them the app can only show what the panels produced, not what the home used or whether you are importing or exporting. Ask the installer to fit them if you want that view.
Can my solar monitoring app be wrong?
Yes, and usually in the reporting, not the panels. Apps lose connection after router changes, and consumption sensors fitted in the wrong place can misreport direction, so the app can show zero while the system produces normally. The inverter's lifetime energy counter and the utility production meter are the reference readings. The lower-than-expected guide works through the split between a reporting fault and a real shortfall.
Why doesn't my app match my utility bill?
Because they measure different things. The app shows what your panels produced; the bill shows what you exported to the grid, after your home used its share. On a day the panels make 30 kWh and the home uses 15 kWh, the app says 30 and the bill credits 15. A gap of 2 to 5 percent between the two is normal; a bigger gap is worth investigating, starting with the consumption sensors.
Why is one panel producing less than the others?
Shade from a new tree or a roof vent, dirt, leaves or bird droppings, or a failing microinverter or optimizer are the usual causes. Open the panel map and tap the low panel: if it reads 20 to 30 percent below its neighbours in full sun, sustained rather than for an hour, it is worth a look on the roof and a note to the installer with a dated screenshot.
My app says the gateway is offline. Are my panels still producing?
Almost certainly yes. The gateway only reports data; it does not control production, so a gateway that loses WiFi leaves the panels working and the app dark. Restart the router first, then reconnect the gateway to the WiFi network. If the gateway shows four blinking red lights, that usually means a hardware failure, and the gateway warranty is five years.
Do I need WiFi for the monitoring app to work?
Yes, for the reporting. The inverter or gateway sends its data to the maker's servers over your home internet, and the app reads it from there, not directly from the equipment on your wall. If the internet goes down, the app stops updating until the connection is restored, and the panels keep producing in the meantime.
Sources and verification
- EnergyScout, How to Use the Enphase Enlighten App: Read November 9, 2026: production view is the default, consumption view needs current transformers (CTs); array view is colour-coded, tap a panel for watts, energy today and microinverter communication; a panel 20 to 30 percent below its neighbours is worth investigating; alerts for system offline, low production and microinverter not reporting; lifetime energy is AC energy; Enlighten updates every 15 minutes; app and utility credits normally agree within 2 to 5 percent; a gateway offline leaves panels producing; IQ Gateway warranty 5 years. Checked November 9, 2026.
- EnergyScout, SolarEdge Monitoring App Guide: How to Use mySolarEdge: Read November 9, 2026: dashboard shows current power in kW, energy today in kWh, and month and year totals, updating every few minutes; the energy flow diagram needs a consumption meter; the power optimizer map is the Layout tab and needs installer-granted layout access; tap a panel for watts, voltage, current and optimizer communication; the app sends no push alerts, email alerts are set in the web portal with a suggested low-production threshold of 70 to 80 percent of expected daily output; S_OK on the inverter display means it is communicating; the homeowner app is monitoring only. Checked November 9, 2026.
- National Laboratory of the Rockies (formerly NREL), PVWatts Calculator: The site's verified record from October 29, 2026: the free site-specific production model used as the independent monthly cross-check. Its results page gives an expected range based on 30 years of actual weather data, computed for a fixed open-rack system; version 8 uses NSRDB typical-year weather. Checked October 29, 2026.
- U.S. Department of Energy, Homeowner's Guide to Solar: The site's verified record from November 8, 2026: the Department of Energy's starting guide for homeowners, linking the step-by-step consumer process, installer choice, and roof replacement timing. Page updated May 15, 2026. Checked November 8, 2026.
App behaviour is from the Enphase Enlighten and mySolarEdge guides read November 9, 2026. PVWatts figures are the site's verified record from October 29, 2026, and the Homeowner's Guide reference is the site's verified record from November 8, 2026. The 320-watt panel reading, the 30 kWh day, and the 933 kWh average month are labelled illustrations with stated inputs, not measurements from any real system. No federal residential credit appears in any figure.